site meter

Minggu, 07 Maret 2010

cara sablon

menyablon stages in my T-shirt with a screen for 3:
1. Pengafdrukan Process:
This process is usually done before the process of printing done (precast). The goal is to create a form appropriate to what we want on the fabric filter (screen), so that when we sweep our printing ink that has been poured on the screen would decrease the extent which we form on the screen.
Expertise in the print process is one important condition to produce a good stencil prints.
And although it seems easy, but many / often for those new to learn techniques menyablon failures in this process. Actually the problem lies in the time radiation / eksposing - him, you have a lot of experimenting to find the proper exposure time.
The process is quite simple, as follows;
1. Clean the screen that we want to use, even though the new screen potentially exposed to dust which can affect the results afdrukan. Clean with soap and dab / cream rag and dry it with a sun screen with a standing position, not a fan because dust lagi.ya catch it? ;-) If ya want cepet pake hairdryer, but his electric bill go up nanti.
2. Apply the medication print / stencil / photo emulsion screens sufficient to rear and front of the screen.
Flatten the drug use Rakel / ruler / coater / paint brush, not too thick / thin. Dry with a hair dryer to dry just because a long time, can also diangin-wind alone but try to be in a place not too exposed to light (dim - dim Ngono, but be careful, ga of word)
3. When dry, prepare your film prints that have been made and glue it on the screen in the position you want (usually in the position of center / center)
There are two options in conducting radiation / exposing, ie, using the sun (good but kagak stable, because it depends on the same generosity of the sun, if the light timing could cepet, klo kagak cloudy can be), or with artificial light (neon light can / UV lamp). This stage requires precise timing, because the print is light-sensitive drugs, so she will react in accordance with the intensity of light it receives (attention: not all drugs are available commercially print requires the same exposure time, you should check with the seller of the drug store about proper exposure time for drugs you buy). The sequence for the solar radiation, glass, film, screen, black cloth pillows (press bearing black so no light came in through the sidelines that resulted in the copy failed), with neon lights 2x40watt, the order the same but ga pake table glass because it menggukanan print.
4. After the irradiation process, the image / shape you want to be seen (somewhat vague - vague) on the screen that has been given a copy these drugs,
Do not be amazed - amazed first saw these pictures, because you have eroded the drug that still cover the print image / shape you want, flush with high pressure water or immersed in water for downed the drug,
Ideally, after you flush the screen or immerse them in water, then copy drugs that have been exposed to light will be eroded away, thus forming the image / shape you want, but sometimes because of the lack of appropriate exposure time, then there may be drugs that are still lagging behind, if you flush with high pressure water, usually the drug itself will fall out eventually, but if you still persist, inevitably you will need to repeat this process from scratch (ouch .. poor you ...)
After the image / shape you want perfectly clean from the disorder drug remaining on the screen, you can dry the screens, or rubbing a screen restorative
Menyablon stages:
1. edge image that will be screened so that the paint does not flow plastered everywhere.
2. put the pasta / rubber mixed pigment / color of your choice.
3. previous use triplex board equipment on the inside so the paint does not penetrate shirt backs.
4. rakel use to sweep the paint. Then dry the shirt.
5. if completed, a screen should be washed immediately with soap and cream patchwork of course with a brush. Although menggukanan berbasir ink water, if the screen is not immediately cleaned the ink will be as difficult to clean oil berbasi.
Tools menyablon a kudu prepared:
1. Screen (gasa cloth made of polyster / Nylon), there are many types of screen, for menyablon shirts / fabric is suitable to use a screen with rough porous type T48, T54, T61, T77, T90 (bigger screen then the value of the higher density, I usually pake T54)
2. Rakel (broom tool is made from synthetic rubber) costs About a 1000-1500 per cm, obtainable in the screen printing shop
3. Drug print (viscous liquid / emulsion) for beginners usually use drugs ulano print type (although expensive) because it is easy to use and before using interfering with sentitizer that have been provided.
4. Mika / paintbrush / coater (copy drug polishing tools)
5. Black pads (for himself, for mengepress movies on screen)
6. Glass with thickness 0.2-0.5mm
7. Water spray (the developer image copy)
8. Ink / paint (special silk-screening) for t-shirts are usually menggukanan pasta color (rubber), white-colored base kilograms and can be mixed with pigment to make paint with desired color.
This is a tutorial how to menyablon t-shirts. Most of the articles and information obtained from



tahap-tahap dalam menyablon kaos dengan screen saya bagi 3 :
1. Proses pengafdrukan :
Proses ini biasanya dilakukan sebelum proses pencetakan dilakukan ( pracetak ). Tujuannya adalah menciptakan bentuk yang sesuai dengan yang kita inginkan diatas kain saring ( screen ), sehingga saat kita menyapu tinta cetak yang telah kita tuangkan diatas screen tersebut akan turun sebatas yang telah kita bentuk diatas screen tersebut.
Keahlian dalam proses afdruk merupakan salah satu syarat penting untuk menghasilkan hasil cetak sablon yang baik.
Dan meskipun kelihatannya mudah, namun banyak / sering sekali bagi mereka yang baru mempelajari teknik menyablon mengalami kegagalan dalam proses ini. Sebenarnya permasalahannya terletak pada waktu penyinaran / eksposing - nya, anda harus banyak bereksperimen untuk menemukan waktu penyinaran yang tepat.
Prosesnya cukup mudah, yaitu sebagai berikut ;
1. Bersihkan screen yang ingin kita gunakan, meskipun baru screen berpotensi terkena debu yang dapat mempengaruhi hasil afdrukan. Bersihkan dengan sabun colek/krim+kain perca lalu keringkan dengan matahari dengan posisi screen berdiri, jangan dengan kipas Karena bisa kena debu lagi.ya kan? ;-) kalo mau cepet ya pake hairdryer, tapi tagihan listrik nya naik nanti.hoho
2. Oleskan obat afdruk / stencil / photo emulsion screen secukupnya ke dibagian belakang dan depan screen.
Ratakan obat tersebut menggunakan Rakel / penggaris / coater/kuas cat,jangan terlalu tebal/tipis. Keringkan dengan hair dryer saja karena keringnya lama sekali,bisa juga diangin-angin saja namun usahakan berada di tempat yang tidak terlalu terekspos oleh cahaya ( remang – remang ngono, tapi hati-hati,ga ketok)
3. Setelah kering, siapkan film sablon yang telah anda buat dan rekatkan pada screen tersebut di posisi yang anda inginkan ( biasanya di posisi center/tengah )
Ada dua pilihan dalam melakukan penyinaran / exposing, yaitu ; menggunakan cahaya matahari ( bagus tapi kagak stabil, soalnya tergantung sama kemurahan hati sang surya, kalo terang waktunya bisa cepet, klo mendung bisa kagak jadi ), atau dengan cahaya buatan ( bisa lampu neon / lampu UV ). Tahapan ini memerlukan timing yang tepat, karena obat afdruk bersifat peka cahaya, sehingga ia akan bereaksi sesuai dengan intensitas cahaya yang diterimanya ( perhatian : tidak semua obat afdruk yang tersedia di pasaran memerlukan waktu penyinaran yang sama, sebaiknya anda tanyakan kepada toko penjual obat tersebut mengenai waktu penyinaran yang tepat untuk obat yang anda beli ). Urutan untuk penyinaran dengan matahari : kaca,film,screen,bantal kain hitam (tekan bantalan hitam agar tak ada cahaya masuk lewat sela-sela yang mengakibatkan proses afdruk gagal), dengan Lampu neon 2x40watt, urutannya sama tapi ga pake kaca karena sudah menggukanan meja afdruk.
4. Setelah proses penyinaran, maka image / bentuk yang anda inginkan akan terlihat ( agak samar – samar ) di atas screen yang telah diberi obat afdruk tersebut,
Jangan terkagum – kagum dulu melihat gambar tersebut, karena anda harus merontokkan obat afdruk yang masih menutupi image / bentuk yang anda inginkan, segera siram dengan air bertekanan tinggi atau benamkan dalam air untuk merontokkan obat tersebut,
Idealnya setelah anda menyiram atau membenamkan screen tersebut dalam air, maka obat afdruk yang telah terekspos cahaya tersebut akan merontokkan diri, sehingga membentuk image / bentuk yang anda inginkan, namun terkadang karena waktu penyinaran yang kurang tepat, maka bisa saja ada obat yang masih tertinggal, bila anda menyiram dengan air bertekanan tinggi, biasanya obat ini akan rontok sendiri pada akhirnya, namun bila masih tetap membandel, mau tidak mau anda perlu mengulang proses ini dari awal ( ouch .. poor you… ),
Setelah image / bentuk yang anda inginkan bersih sempurna dari gangguan obat yang masih tersisa di screen, anda dapat mengeringkan screen tersebut, atau mengoleskan obat penguat screen
Tahapan Menyablon :
1. pinggiran gambar yang akan disablon diplester agar cat tidak mengalir kemana-mana.
2. letakkan pasta/rubber yang sudah dicampur pigment/warna yang diinginkan.
3. sebelumnya gunakan alat papan triplex pada bagian dalam kaos agar cat tidak tembus kebelakang.
4. gunakan rakel untuk menyapu cat. Lalu keringkan kaos.
5. jika sudah selesai, sebaiknya screen langsung dicuci dengan sabun krim tentu dengan kain perca sebagai sikatnya. Walaupun menggukanan tinta berbasir air, apabila screen tidak langsung dibersihkan akan sesulit membersihkan tinta berbasi minyak.
Peralatan menyablon yang kudu disiapkan :
1. Screen (kain gasa terbuat dari polyster/nylon), ada banyak jenis screen, untuk menyablon kaos/kain maka cocok menggunakan screen berpori-pori kasar dengan type T48,T54,T61,T77,T90 (nilai screen semakin besar maka kerapatannya semakin tinggi,saya biasanya pake T54)
2. Rakel (alat sapu terbuat dari karet sintesis) harganya sekita 1000-1500 per cm, dpt dibeli di toko sablon
3. Obat afdruk (cairan kental/emulsion) untuk pemula biasanya menggunakan obat afdruk jenis ulano (meskipun mahal) karena mudah untuk digunakan dan sebelum menggunakan campur dengan sentitizer yang telah disediakan.
4. Mika/kuas cat/coater (alat pemoles obat afdruk)
5. Bantalan Hitam (buat sendiri, untuk mengepress film pada screen)
6. Kaca dengan tebal 0.2-0.5mm
7. Semprotan Air (pengembang gambar hasil afdruk)
8. Tinta/cat (khusus sablon) untuk kaos biasanya menggukanan pasta warna (rubber), bewarna dasar putih kentar dan dapat dicampur pigment untuk membuat cat dengan warna yang diinginkan.
Inilah tutorial cara menyablon kaos. Sebagian besar artikel dan informasi diperoleh dari hanzoprinting.com


Cara Membuat Stiker/Sticker Sederhana - Kreasi Keterampilan Prakarya
Tue, 30/06/2009 - 12:40am — godam64
Buat adik-adik kecil semua kini dapat membuat kerajinan tangan hasil kreativitas sendiri gambar tempel / stiker dengan bahan-bahan sederhana yang dapat kita temui di rumah atau di toko-toko buku kesayangan adik-adik semua. Dalam membuat prakarya tersebut sebaiknya didampingi oleh orang tua atau orang dewasa agar hasilnya bagus.
Bahan :
Kertas karton manila, lem kertas, cuka, potongan gambar dari majalah.
Cara Membuat Stiker :
1. Tempel kertas karton manila di balik potongan gambar dari majalah dengan lem kertas.
2. Campur dan aduk cuka dengan lem kertas dengan perbandingan 1 banding 2.
3. Oles campuran cuka lem tadi di belakang kertas karton manila yang tidak ada gambarnya lalu keringkan. Selesai.
4. Jika hendak menempelkan gambar tempel yang tadi dibuat, tinggal diberi sedikit air di bagian yang diolesi campuran cuka lem lalu tempel di tempat yang akan ditempeli gambar tempel.
Selamat mencoba semoga berhasil.